Troubleshooting Husqvarna Sewing machine parts

Husqvarna sewing machines are known for their high-quality and durability, but like any other machine, they can encounter problems. Troubleshooting these problems can be challenging, especially if you don’t have much experience with sewing machines. However, with a little knowledge and guidance, you can troubleshoot and fix most issues with your Husqvarna sewing machine parts.

In this guide, we’ll cover some common problems you may encounter with your Husqvarna sewing machine parts, including the causes of these issues and step-by-step troubleshooting instructions.

List of the 15 Commonly Broken Husqvarna Sewing Machine Parts

Here are some common parts of the Husqvarna sewing machine that may break or malfunction:

Needle and needle clamp
Tension disks
Bobbin case

Bobbin winder
Feed dog
Slide plate

Presser foot lever
Presser dial
Sewing light

Take-up lever
Throat plate
Motor belt

Power cord
Foot pedal
Thread cutter.

Common Husqvarna Sewing Machine Parts Problems and Solutions

When any of the above parts of the Husqvarna sewing machine break, it can cause problems in the overall functioning of the machine. Below, we will discuss each of these parts’ problems, their causes, and how to fix them.

Husqvarna Sewing Machine Motor Problems

If your Husqvarna sewing machine motor stops running, runs slowly, or makes unusual noises, then it is time to troubleshoot it.

Causes of Husqvarna Sewing Machine Motor Problems

Dust and debris buildup in the motor.

Lack of lubrication in the motor.
Wiring problems.
Overheating.

Troubleshooting Husqvarna Sewing Machine Motor Problems

Clean the motor using a soft-bristled brush.
Lubricate the motor according to the manufacturer’s instructions.
Check the wiring connections and repair or replace any damaged wires.

Allow the motor to cool down if it has overheated.

Husqvarna Sewing Machine Belt Problems

If your Husqvarna sewing machine belt breaks, it can cause the machine to stop running or run at a slower speed.

Causes of Husqvarna Sewing Machine Belt Problems

Lack of tension in the belt.

Wear and tear on the belt.
Incorrectly installed belt.

Troubleshooting Husqvarna Sewing Machine Belt Problems

Check the tension of the belt and adjust it if necessary.

Replace the belt if it is worn or damaged.
Reinstall the belt correctly if it is installed incorrectly.

Husqvarna Sewing Machine Presser Foot Problems

If the presser foot on your Husqvarna sewing machine is not holding the fabric down properly, it can cause uneven stitching or skipped stitches.

Causes of Husqvarna Sewing Machine Presser Foot Problems

Dirty or damaged presser foot.
Incorrect presser foot pressure.
Improper presser foot attachment.

Troubleshooting Husqvarna Sewing Machine Presser Foot Problems

Clean or replace the presser foot if it is dirty or damaged.
Adjust the presser foot pressure according to the manufacturer’s instructions.
Ensure that the correct presser foot is attached to the machine and that it is installed correctly.

How To Fix Presser Foot On Husqvarna

If the presser foot on your Husqvarna sewing machine is not working properly, there are a few steps you can take to troubleshoot and fix the issue:

Check the Presser Foot Lever: The first thing you should check is whether the presser foot lever is up or down. If it’s down, you won’t be able to lift the presser foot. Simply raise the lever to lift the presser foot.
Clean the Presser Foot and Feed Dogs: Dust, lint, and thread can accumulate on the presser foot and feed dogs, which can cause the presser foot to not work properly. Clean the presser foot and feed dogs with a soft brush and/or a lint roller.

Adjust the Presser Foot Pressure: If the presser foot is not applying enough pressure, it won’t hold the fabric in place properly. Adjust the presser foot pressure according to your sewing machine’s manual. On most Husqvarna sewing machines, you can adjust the presser foot pressure by turning a dial on the machine.
Replace the Presser Foot: If none of the above steps work, it’s possible that the presser foot itself is damaged or worn out. Replace the presser foot with a new one.

Husqvarna sewing machine thread cutter problems

The thread cutter on a Husqvarna sewing machine may not cut the thread cleanly or at all, or it may be dull and need to be replaced.

Causes of the Husqvarna Sewing machine thread cutter problems

Buildup of lint or debris around the thread cutter blade.
A dull or damaged blade.
Improper use or maintenance of the thread cutter.

Troubleshooting Husqvarna Sewing machine thread cutter problems

Turn off the Husqvarna sewing machine and unplug it from the power source.
Use a small brush or compressed air to clean the area around the thread cutter blade, removing any lint or debris.
Test the thread cutter to see if it is cutting cleanly. If it is still not cutting well, replace the blade with a new one. Follow the manufacturer’s instructions for replacing the blade.

If the problem persists, check the machine manual for specific instructions on adjusting the thread cutter. If adjustment is required, follow the instructions provided.
Turn on the machine and test the thread cutter to make sure it is working properly.

Hand wheel problems on Husqvarna sewing machine

The hand wheel on a Husqvarna sewing machine may become difficult to turn or may not turn at all.

Causes of the Husqvarna Sewing machine hand wheel problems

Buildup of lint or debris in the machine.
A loose or damaged drive belt.
A jammed machine.

Troubleshooting Husqvarna Sewing machine hand wheel problems. How To Fix Husqvarna Sewing Machine Handwheel

Turn off the Husqvarna sewing machine and unplug it from the power source.
Remove the needle and the bobbin case from the machine.
Use a small brush or compressed air to clean the area around the hand wheel and the machine, removing any lint or debris.

Check the drive belt to make sure it is not loose or damaged. If it is, replace it with a new one.
Check the machine for any jams. Remove any fabric or thread that may be causing the jam.
Turn the hand wheel manually to see if it turns smoothly. If it does, reassemble the machine and test it. If it does not turn smoothly, the problem may be more serious and require professional repair.

Husqvarna sewing machine Foot Pedal, Power Cord and Switch problems

The foot pedal, power cord, and switch are essential components of the Husqvarna sewing machine that can encounter problems. The foot pedal controls the speed of the machine, while the power cord and switch are responsible for powering it. If any of these components fail, it can prevent the machine from functioning properly.

Causes of the Husqvarna sewing machine Foot Pedal, Power Cord and Switch problems

Faulty foot pedal: The foot pedal may fail to work if there is a broken wire, loose connection or it has worn out over time.
Damaged power cord: A frayed, cut or broken power cord can lead to the machine not getting any power.

Faulty switch: If the switch is not working, the machine may not turn on or off.

Troubleshooting Husqvarna sewing machine Foot Pedal, Power Cord and Switch problems

Check the power source: Ensure the power cord is correctly plugged in and the outlet is working. Try plugging in the cord in a different socket and test the machine again.
Check the foot pedal: Inspect the foot pedal for any signs of damage or wear. Check the wires for any cuts or loose connections. If there are any faults, replace the foot pedal with a new one.

Check the switch: Inspect the switch for any damage or wear. Test the switch by turning it on and off several times. If the switch is not working, replace it with a new one.
Check the power cord: Inspect the power cord for any damage, cuts or frays. If there are any faults, replace the power cord with a new one.

Husqvarna sewing machine Reverse Lever problems

The reverse lever on a Husqvarna sewing machine is used to sew in reverse, creating a backstitch at the beginning and end of a seam. If the reverse lever is not working, it can make it challenging to sew certain fabrics or projects.

Causes of the Husqvarna sewing machine Reverse Lever problems

Broken reverse lever: The reverse lever can break if it is used excessively or if it is made of weak materials.
Dirt or debris: Dirt, dust, or debris can accumulate on the reverse lever, making it difficult to move or engage.
Misaligned or worn-out parts: Over time, parts of the machine can become misaligned or worn out, causing the reverse lever to malfunction.

Troubleshooting Husqvarna sewing machine Reverse Lever problems

Clean the reverse lever: Use a soft cloth or brush to remove any dirt or debris that may have accumulated on the reverse lever. Lubricate it with a drop of sewing machine oil or silicone lubricant.
Check for broken or worn-out parts: Inspect the reverse lever and its mechanism for any visible damage or wear. Replace any worn or broken parts.
Adjust the reverse lever: Check the alignment of the reverse lever and make any necessary adjustments. If the lever is too tight or loose, adjust it using the tension screw.

Husqvarna sewing machine Spool Pin and Holder problems

The spool pin and holder on a Husqvarna sewing machine are responsible for holding the thread spool in place. If the spool pin or holder is damaged or not working correctly, it can cause the thread to tangle or break during sewing.

Causes of the Husqvarna sewing machine Spool Pin and Holder problems

Spool pin or holder is damaged or broken
The spool pin or holder is not installed properly

The spool pin or holder is dirty or has debris stuck in it

Troubleshooting Husqvarna sewing machine Spool Pin and Holder problems

Turn off the machine and unplug it.
Check if the spool pin or holder is installed properly. If not, reinstall it according to the manufacturer’s instructions.

If the spool pin or holder is dirty, clean it with a soft cloth and remove any debris stuck in it.
Check if the spool pin or holder is damaged or broken. If so, replace it with a new one.

Husqvarna sewing machine Pattern Selector problems

The pattern selector on the Husqvarna sewing machine is not working properly. The machine may not switch between stitches or may be stuck on one stitch.

Causes of the Husqvarna sewing machine Pattern Selector problems

The pattern selector dial is not aligned properly
The pattern selector is dirty or has debris stuck in it
The pattern selector mechanism is damaged or broken

Troubleshooting Husqvarna sewing machine Pattern Selector problems

Turn off the machine and unplug it.
Check if the pattern selector dial is aligned properly. If not, realign it according to the manufacturer’s instructions.
If the pattern selector is dirty, clean it with a soft cloth and remove any debris stuck in it.

Check if the pattern selector mechanism is damaged or broken. If so, it may need to be replaced by a professional technician.

Husqvarna sewing machine Stitch Length Adjustment problems

The stitch length adjustment on the Husqvarna sewing machine is not working properly. The machine may not change stitch length or may be stuck on one stitch length.

Causes of the Husqvarna sewing machine Stitch Length Adjustment problems

The stitch length adjustment dial is not aligned properly

The stitch length adjustment mechanism is dirty or has debris stuck in it
The stitch length adjustment mechanism is damaged or broken

Troubleshooting Husqvarna sewing machine Stitch Length Adjustment problems

Turn off the machine and unplug it.

Check if the stitch length adjustment dial is aligned properly. If not, realign it according to the manufacturer’s instructions.
If the stitch length adjustment mechanism is dirty, clean it with a soft cloth and remove any debris stuck in it.
Check if the stitch length adjustment mechanism is damaged or broken. If so, it may need to be replaced by a professional technician.

Husqvarna sewing machine Tension Disks problems

The tension disks are responsible for regulating the tension of the upper thread as it feeds through the sewing machine. If the tension disks are not functioning properly, the upper thread may be too loose or too tight, resulting in uneven or skipped stitches.

Causes of the Husqvarna sewing machine Tension Disks problems

Dirt or debris in the tension disks
Improper threading of the upper thread

Damaged or worn tension disks
Incorrect tension settings
Incorrect needle size for the thread being used

Troubleshooting Husqvarna sewing machine Tension Disks problems

Turn off the sewing machine and unplug it from the power source.
Remove the upper thread from the machine and lift the presser foot.
Use a small brush or compressed air to clean any dirt or debris from the tension disks.

Re-thread the machine, making sure the thread is properly threaded through the tension disks.
Adjust the tension setting according to the fabric and thread being used.
Make sure the needle is the correct size for the thread being used.

Test the machine on a scrap piece of fabric to ensure the tension is correct and the stitches are even.

Husqvarna sewing machine Needle and Needle Clamp problems

The needle and needle clamp are crucial components of the sewing machine, responsible for holding the needle in place and allowing it to penetrate the fabric. If there are issues with the needle or needle clamp, the machine may not sew properly or the needle may break.

Causes of the Husqvarna sewing machine Needle and Needle Clamp problems

Incorrect needle size for the fabric being used

Worn or damaged needle
Loose or damaged needle clamp
Incorrect needle installation

Troubleshooting Husqvarna sewing machine Needle and Needle Clamp problems

Turn off the sewing machine and unplug it from the power source.
Remove the needle and needle clamp from the machine.
Check the needle to ensure it is the correct size for the fabric being used and that it is not worn or damaged.

Check the needle clamp for any signs of wear or damage, such as cracks or chips.
Make sure the needle clamp is tightened securely onto the needle.
Reinstall the needle and needle clamp, making sure the needle is inserted correctly and tightened securely.

Test the machine on a scrap piece of fabric to ensure the needle is functioning properly and the stitches are even.

Husqvarna sewing machine Take-Up Lever problems

The Take-Up Lever is responsible for moving the thread up and down while sewing. If there is a problem with the Take-Up Lever, the thread may become tangled or the machine may not sew properly.

Causes of the Husqvarna sewing machine Take-Up Lever problems

Lack of maintenance.

Bent or damaged Take-Up Lever.
Incorrect threading of the machine.
Worn-out parts.

Dirt or lint buildup.

Troubleshooting Husqvarna sewing machine Take-Up Lever problems

Turn off the sewing machine and unplug it from the power source.
Remove the needle and the presser foot from the machine.

Open the cover of the machine and locate the Take-Up Lever.
Check the Take-Up Lever for any visible signs of damage or wear.
If the Take-Up Lever is bent or damaged, it will need to be replaced. Contact a professional Husqvarna service technician for assistance.

If the Take-Up Lever appears to be in good condition, check the threading of the machine to make sure it is correct. Refer to the user manual for proper threading instructions.
Clean any dirt or lint buildup around the Take-Up Lever using a soft brush or lint roller.
If the problem persists, contact a professional Husqvarna service technician for further assistance.

Husqvarna sewing machine Presser Dial problems

The Presser Dial is responsible for adjusting the pressure of the presser foot on the fabric. If there is a problem with the Presser Dial, the fabric may not feed through the machine properly, causing uneven stitches or skipped stitches.

Causes of the Husqvarna sewing machine Presser Dial problems

Lack of maintenance.
Incorrect adjustment of the Presser Dial.

Worn-out parts.
Dirt or lint buildup.
Damage to the Presser Dial.

Troubleshooting Husqvarna sewing machine Presser Dial problems

Turn off the sewing machine and unplug it from the power source.
Open the cover of the machine and locate the Presser Dial.
Check the Presser Dial for any visible signs of damage or wear.

If the Presser Dial is damaged, it will need to be replaced. Contact a professional Husqvarna service technician for assistance.
If the Presser Dial appears to be in good condition, make sure it is adjusted properly. Refer to the user manual for proper adjustment instructions.
Clean any dirt or lint buildup around the Presser Dial using a soft brush or lint roller.

If the problem persists, contact a professional Husqvarna service technician for further assistance.

Husqvarna sewing machine Feed Dog problems

The feed dog is a component located underneath the needle plate that helps move the fabric through the sewing machine. If the feed dogs are not working properly, the fabric may not be fed through the machine correctly, resulting in uneven stitches, skipped stitches, or no movement of the fabric at all.

Causes of the Husqvarna sewing machine Feed Dog problems

Dirt or debris stuck in the teeth of the feed dogs.
Worn or damaged feed dogs.
Incorrect adjustment of the feed dog height.
Broken or worn-out feed dog spring.

Troubleshooting Husqvarna sewing machine Feed Dog problems

Turn off the machine and unplug it from the power source.
Remove the needle plate and check the feed dogs for any dirt or debris. Clean them thoroughly using a small brush or a vacuum cleaner.
Check the feed dogs for any signs of wear or damage. If the teeth are worn or damaged, they will need to be replaced.
Adjust the feed dog height according to the user manual. If the feed dogs are too low or too high, they may not be able to move the fabric through the machine properly.
Check the feed dog spring for any signs of wear or damage. If the spring is broken or worn out, it will need to be replaced.
Replace the needle plate and turn on the machine. Test the machine on a scrap piece of fabric to see if the feed dogs are working properly. If the problem persists, it may be best to take the machine to a professional for further inspection and repair.

Husqvarna sewing machine Throat Plate problems

The throat plate, also known as the needle plate, is a metal plate located beneath the presser foot and holds the fabric flat while it is being stitched. If the throat plate is damaged or worn out, it can cause the fabric to get caught or feed improperly through the machine.

Causes of the Husqvarna sewing machine Throat Plate problems

Dirt or debris stuck in the throat plate channel.
Wear and tear due to prolonged use.
Incorrect installation of the throat plate.
Damage due to dropping or mishandling the machine.

Troubleshooting Husqvarna sewing machine Throat Plate problems

Turn off the machine and unplug it from the power source.
Remove the needle plate and throat plate.
Check the throat plate for any dirt or debris. Clean it thoroughly using a small brush or a vacuum cleaner.
Inspect the throat plate for any signs of wear or damage. If it is worn or damaged, it will need to be replaced.
Reinstall the throat plate, ensuring that it is properly aligned with the needle plate and the feed dogs.
Replace the needle plate and turn on the machine. Test the machine on a scrap piece of fabric to see if the throat plate is functioning properly. If the problem persists, it may be best to take the machine to a professional for further inspection and repair.

Husqvarna sewing machine Presser Foot Lever problems

The presser foot lever on a Husqvarna sewing machine can sometimes become difficult to move, making it hard to change the presser foot or adjust its pressure. In some cases, the lever may not move at all, preventing the presser foot from lowering onto the fabric.

Causes of the Husqvarna sewing machine Presser Foot Lever problems

There are several potential causes of problems with the presser foot lever on a Husqvarna sewing machine, including:

Dirt or debris: Over time, dirt, lint, and other debris can build up around the presser foot lever, making it harder to move.
Stiff or stuck mechanism: The mechanism that moves the presser foot lever up and down may become stiff or stuck due to lack of lubrication or wear and tear.
Misalignment: The presser foot lever and its associated parts may become misaligned, preventing the lever from moving smoothly.
Damaged parts: Any of the parts associated with the presser foot lever may become damaged, such as the lever itself, the spring that controls it, or the connecting rod that moves it.

Troubleshooting Husqvarna sewing machine Presser Foot Lever problems

If you’re experiencing problems with the presser foot lever on your Husqvarna sewing machine, try the following troubleshooting steps:

Clean the area around the presser foot lever. Use a soft, dry cloth to remove any dirt, lint, or debris that may have accumulated around the lever.
Check for stiffness or sticking. Gently move the presser foot lever up and down to see if it moves smoothly. If it doesn’t, try adding a drop of sewing machine oil or lubricant to the mechanism that controls the lever. Move the lever up and down several times to distribute the oil.
Check for misalignment. If the lever still doesn’t move smoothly after adding oil, you may need to realign the parts that control the lever. Refer to your sewing machine manual for instructions on how to do this.
Check for damaged parts. If the above steps don’t solve the problem, you may need to replace one or more parts associated with the presser foot lever. Check your sewing machine manual or contact a professional for assistance.

Husqvarna sewing machine Sewing Light problems

The sewing light on a Husqvarna sewing machine can sometimes stop working or become dim, making it difficult to see what you’re sewing.

Causes of the Husqvarna sewing machine Sewing Light problems

There are several potential causes of problems with the sewing light on a Husqvarna sewing machine, including:

Burned-out bulb: The bulb that provides light may have burned out and need to be replaced.
Loose or broken wiring: The wiring that connects the bulb to the machine may be loose or broken, preventing electricity from reaching the bulb.
Faulty switch: The switch that turns the light on and off may be faulty, preventing it from working properly.
Faulty power supply

Troubleshooting Husqvarna sewing machine Sewing Light problems:

Check the bulb: Turn off the machine and unplug it. Locate the light bulb cover and remove it.
Check if the bulb is burnt out or damaged. If so, replace the bulb with a new one of the same wattage.
Check the wiring: Turn off the machine and unplug it. Check if the wiring from the light bulb is loose or disconnected. If so, reconnect the wiring or replace it if damaged.
Check the switch: Turn off the machine and unplug it. Locate the light switch and check if it is functioning properly. If the switch is faulty, it needs to be replaced.
Check the power supply: Turn off the machine and unplug it. Check if the power supply is faulty by using a multimeter to test the voltage. If the power supply is faulty, it needs to be repaired or replaced.

Husqvarna sewing machine Slide Plate problems

The slide plate on a Husqvarna sewing machine is a part that covers the bobbin case and protects it from damage during sewing. If the slide plate is not functioning properly, it can cause several issues, including difficulty in threading the needle, bobbin case jamming, and poor stitch quality.

Causes of the Husqvarna sewing machine Slide Plate problems

Dirt and debris buildup under the slide plate.
Misalignment of the slide plate.
Worn or damaged slide plate.

Troubleshooting Husqvarna sewing machine Slide Plate problems

Turn off the sewing machine and unplug it from the power source.
Remove the presser foot and needle from the machine.
Open the slide plate by sliding it towards you.
Inspect the slide plate and the area underneath it for dirt, lint, and debris. If you find any, clean the area with a soft-bristled brush and a lint roller.
Check if the slide plate is misaligned. If it is, try to reposition it by gently pushing it into place. If it does not move, you may need to consult a professional to repair or replace the slide plate.
Examine the slide plate for any visible signs of wear or damage. If the slide plate is damaged, it should be replaced with a new one.

Husqvarna sewing machine Bobbin Case problems

The bobbin case on a Husqvarna sewing machine holds the bobbin in place while sewing. If the bobbin case is not functioning properly, it can cause several issues, including difficulty in threading the needle, bobbin thread tangling, and poor stitch quality.

Causes of the Husqvarna sewing machine Bobbin Case problems

Dirt and debris buildup in the bobbin case.
Misalignment of the bobbin case.
Worn or damaged bobbin case.

Troubleshooting Husqvarna sewing machine Bobbin Case problems

Turn off the sewing machine and unplug it from the power source.
Remove the needle and the presser foot from the machine.
Open the bobbin case by pushing the latch on the case and pulling it out.
Inspect the bobbin case and the area around it for dirt, lint, and debris. If you find any, clean the area with a soft-bristled brush and a lint roller.
Check if the bobbin case is misaligned. If it is, try to reposition it by gently pushing it into place. If it does not move, you may need to consult a professional to repair or replace the bobbin case.
Examine the bobbin case for any visible signs of wear or damage. If the bobbin case is damaged, it should be replaced with a new one.

Husqvarna sewing machine Bobbin problems

The bobbin is not correctly inserted or positioned, causing it to thread improperly or not at all. The bobbin thread may also bunch or tangle under the fabric.

Causes of the Husqvarna sewing machine Bobbin problems

Incorrect bobbin size for the machine
Bobbin inserted incorrectly or not positioned properly
Bobbin tension is too tight or too loose
Bobbin thread is wound unevenly or loosely
Bobbin case is damaged or worn

Troubleshooting Husqvarna sewing machine Bobbin problems

Turn off the machine and unplug it from the power source.
Remove the bobbin case and check for any signs of damage or wear.
Remove the bobbin and make sure it is the correct size and inserted correctly.
Check the tension of the bobbin by holding the thread and letting it dangle. It should have a slight tension but not be too tight or too loose.
If the tension is too tight, loosen the tension screw on the bobbin case. If it’s too loose, tighten the screw.
Check the bobbin thread and make sure it’s wound evenly and not too loosely.
Reinsert the bobbin case and bobbin correctly.
Try sewing on scrap fabric to test the bobbin thread tension and see if the problem is resolved.

Husqvarna sewing machine Bobbin Winder problems

The bobbin winder may not be working or may not wind the thread evenly onto the bobbin.

Causes of the Husqvarna sewing machine Bobbin Winder problems

The bobbin winder tire is worn or needs to be cleaned
The bobbin winder spindle is loose or damaged
The bobbin winder stopper is not engaging properly
The machine’s belt is worn or needs to be adjusted

Troubleshooting Husqvarna sewing machine Bobbin Winder problems

Turn off the machine and unplug it from the power source.
Remove the bobbin and bobbin case.
Remove the bobbin winder tire and clean it with a soft cloth or replace it if it’s worn.
Check the bobbin winder spindle and make sure it’s not loose or damaged. Tighten or replace it if necessary.
Check the bobbin winder stopper and make sure it’s engaging properly with the bobbin winder spindle.
If the bobbin winder still isn’t working, check the machine’s belt and adjust or replace it if necessary.
Reinsert the bobbin and bobbin case and try winding the bobbin again.

10 Other Problems with Husqvarna Sewing Machines

In addition to the problems already mentioned in this article, there are a few other issues that can arise with Husqvarna sewing machines. These include:

FAQ

How do I know which type of needle is suitable for my Husqvarna sewing machine?

It is recommended to refer to the owner’s manual of your machine, as it usually lists the compatible needle types and sizes. You can also check the packaging of the needles for information.

Can I use a universal foot on my Husqvarna sewing machine?

While a universal foot may fit on your machine, it is always best to use the specific foot designed for your model. Using a universal foot may affect the quality of your sewing or damage your machine.

How often should I replace the bobbin case on my Husqvarna sewing machine?

It depends on the frequency and intensity of your sewing. If you notice any irregularities in the bobbin thread tension or if the bobbin case is visibly damaged, it is best to replace it. Otherwise, it is recommended to replace it every 2-3 years.

Can I use a different brand of thread on my Husqvarna sewing machine?

Yes, you can use other brands of thread on your machine, but it is recommended to use high-quality thread that is suitable for your sewing project. Poor quality thread may cause breakages or tension issues.

Can I adjust the tension of the presser foot on my Husqvarna sewing machine?

No, the presser foot tension is not adjustable on most Husqvarna sewing machine models. The tension is set by the machine and is not meant to be changed.

Conclusion. Troubleshooting Husqvarna Sewing machine parts

Troubleshooting your Husqvarna sewing machine parts can be a daunting task, but with the right information and approach, you can quickly identify and fix most issues. Always remember to consult your user manual or contact a certified technician if you encounter a problem you can’t fix on your own.

By keeping your machine well-maintained and addressing any issues promptly, you can enjoy many years of trouble-free sewing with your Husqvarna sewing machine.